"The Holy Grail" - TEA@CPP's Retro Rewind Escape Room
Industrial-grade radar sensor aggregator board that bridges 12x LD2410C 24GHz sensors to an ESP32 via a buffered UART-to-SPI network. Features dual-stage voltage regulation, bus isolation, temperature control, and dedicated serial and networking ports.
Consolidates 12 independent, high-frequency LD2410C radar modules into a central aggregation hub.
Employs various signal trace optimizations like differential pair tuning and multi-layer ground planes.
Integrates signal reliability features like clock buffers and series termination resistors, to further bolster data integrity.
Manages network protocols using a dedicated Ethernet controller to streamline communication with the show network.
Deploys a dual-stage power solution that steps down 12V to 5V and 5V to 3.3V, providing reliable power for all components and sensors from a single power terminal.
Includes a hardware-controlled thermal management system that triggers a fan when temperatures reaches over 65 C.
Incorporates a robust DB-25 connector to secure sensor cables to the board.
Designated a 6-layer board stack-up to isolate signal lines from power and ground planes, increasing signal integrity even further.
First test code upload and proof of serial communication.
4 hour stress-test before installation. Experimental temperatures were far below expected, making this board capable in harsh thermal climates.
"The Lost Ark" - TEA@CPP's Retro Rewind Escape Room
Custom weight-sensing controller that reads a load-cell strain gauge through a high-resolution ADS1232. Features USB-C programming and serial debugging, regulated power, configurable weight-detection logic, and a DRV8871 motor driver for activating a 12 V motor when the target weight is reached.
Electrical Team | UAV Power Distribution & PCB Design
Developed a high-current power distribution PCB designed to manage over 150 A of combined electrical loads across UAV avionics, radar, and propulsion systems, supporting a targeted flight endurance of over 40 minutes.
Designed a dual-battery power management architecture integrating 12S and 5S battery systems through a power multiplexer (MUX), enabling coordinated power distribution and improved system reliability.
Collaborated with a multidisciplinary team of electrical engineers as the sole mechanical engineering student, applying mechanical design principles to improve PCB durability, component integration, and structural resilience.
Incorporated design-for-reliability and serviceability considerations to improve electrical robustness, mechanical survivability, and component accessibility following potential crash events.
Senior Design Project | Electronics & PCB Design
Designed a custom 4-layer PCB integrating an ESP32-S3 microcontroller, INA219 current sensors, H-bridge motor drivers, and power regulation circuitry to support precise actuation of a cable-driven soft robotic manipulator.
Implemented INA219 current sensing to characterize the relationship between motor current draw and cable tension, enabling electrical feedback to inform grasping force estimation and motor control.
Developed and conducted experimental testing procedures to evaluate motor current, tensile force, and PWM duty cycle, identifying a near-linear relationship between force and duty cycle, and characterizing motor current behavior.
Optimized PCB architecture and signal integrity through a dedicated ground plane, power distribution layer, and separated motor driver circuits, mitigating electrical interference and improving current measurement reliability.
Identified electrical operating limitations associated with the INA219's 3.2 A measurement ceiling, establishing a practical PWM duty-cycle limit of approximately 60–62% while achieving up to 30 N of measured tensile force.
A render of the 4-layer PCB design used for this animatronic.
Our data correlating current to duty cycle, as well as force to duty cycle.
Embedded Systems Architecture | System Logic & Hardware Integration
Developed a conceptual embedded security system architecture integrating microcontroller-based control, SIM7020G cellular communication, GPS tracking, and electronic locking mechanisms to support remote bicycle security monitoring.
Designed a comprehensive state-based control flowchart coordinating lock engagement, alarm activation, physical key detection, and remote security notifications through interconnected hardware and software processes.
Established fault-handling and recovery procedures for cellular connectivity failures, hardware initialization errors, and communication timeouts, incorporating non-volatile state retention to support system reliability.
Defined hardware interfaces and operational sequences for cellular communication, GPS location acquisition, audible alarms, and LED status indicators, establishing a foundation for future firmware development and physical prototyping.